Displacement Determination by Holographic Interferometry for Residual Stress Analysis in Elastic Bodies

A method is developed for determining the three displacement components by the method of holographic interferometry from two interferograms used to measure residual stresses by hole drilling. The displacements are determined at the intersection points of the principal axes and the hole boundary. The method is experimentally validated by measuring the stress state of a plate under uniaxial tension __________ Translated from Prikladnaya Mekhanika, Vol. 41, No. 8, pp. 111–117, August 2005.     

MEASUREMENT OF ADHESION FORCES IN AIR WITH THE VIBRATION METHOD

The vibration method represents a practical method for the measurement of adhesion forces and adhesion force distributions. This method causes sinusoidally altemating stresses and yields detachment and contact forces between particles and substrate of the same order of magnitude. Alternating contact forces of the vibration method can cause an adhesion force intensification through flattening of asperities. The measuring principle of the vibration method and the analysis of experimental results are described in the article. Normal adhesion forces (pull-off forces) are measured using the vibration method and the colloidal probe technique. The results of both methods show good agreement for small particle sizes. The influence of the detachment force direction is shown by comparing tangential and normal adhesion forces measured using particle reentrainment in a turbulent air flow and the vibration method, respectively. The surface roughness of the substrate and the relative humidity are shown to significantly influence the measured adhesion forces. For the calculation of the adhesion forces, an approach by Rabinovich was combined with approximations of plastic micro asperity flattening. The Rabinovich approach accounts for roughness effects on the van der Waals force by incorporating the rms roughness of the interacting surfaces. rms-values of the particles and substrates were measured with atomic force microscopy at different scanning areas.     

京承高速公路新道沟连拱隧道的优化设计

本文以京承高速公路新道沟连拱隧道为实例,应用有限元数值方法对连拱隧道二次衬砌的围岩抗力、应力、变形及其稳定性等问题进行了模拟与分析。首先,基于连拱衬砌的结构型式,作者建立了该隧道的数值模型,并提出用弹性杆单元按作用力等效的原则模拟围岩抗力;根据数值模拟结果对隧道支护结构的承载能力进行了讨论,并基于规范对二次衬砌进行了结构强度校核。该研究结果为新道沟隧道支护结构设计的优化提供了科学依据。     

The interaction of doubly periodic cracks

In this paper, an extremely accurate and efficient method for computing the interaction of a set of or multiple sets of general doubly periodic cracks has been presented on the basis of superposition principle, pseudo-traction method, and isolating analysis technique. A great number of typical examples are given in this paper. The stress intensity factors (SIF), the minimum strain energy density factors (SED) of crack tip and the critical stress (CRS) of crack growth are calculated with the accuracy of six significant digits for the rectangularly distributed periodic cracks and five significant digits for the general doubly periodic cracks. The relation of the interaction effect of the double periodic cracks with the periods and the ratio of crack length to crack spacing is analyzed. Also in this paper, the key technique problems for this method are discussed.     

复杂边界条件下渗流场流线分布研究

流线分布研究已受到油藏工程师们的普遍关注。本文从无限大油藏稳态渗流场基本解出发,结合边界元方法求解出复杂边界条件下稳态渗流场的势分布,以此为基础提出了流线场的生成办法,并给出了应用实例。本文方法的优点在于求解过程中将问题的维数降低了一维,减少了计算量;计算精度较高且具有一定的普遍应用性;适应于求解任意形状的包括定压、定流量或混合边界在内的组合边界问题。实例表明,利用本文方法产生的流线分布因能够较为直观地反映出油藏流体在注采井间的运动轨迹,为优化井网和注入方案提供了重要依据。     

后台阶流动的数值模拟

访述了大涡模拟的基本思想，指出大涡模拟的效率主要取决于四个因素，即流动中须有大尺度涡存在、合理的计算格式、合适的滤波器和亚格子应力模型。在深入考虑粘性不可压缩流Navier—Stokes方程各个子项作用的基础上，提出二阶全展开Euler—Taylor—Galerkin有限元方法作为大涡模拟的离散格式，并采用Gauss滤波器，对典型算例——后台阶处的流动进行大涡模拟，计算结果与相关文献符合的很好。从计算结果还可以看出大涡模拟与二阶全展开ETG有限元方法的结合在捕捉涡系及反映涡动时变过程方面具有明显的优势，说明大涡模拟适合于边界几何形状复杂区域流动的模拟。同时应用二阶全展开ETG有限元方法对低雷诺数粘性不可压缩后台阶流动进行了计算，得到与相关文献符合良好的计算结果，即该方法也可独立用于对低雷诺数粘性不可压缩流动的计算。     

界面特性对短纤维金属基复合材料蠕变行为的影响

基于短纤维增强金属基复合材料(MMC)的单纤维三维模型(三相)，利用粘弹性有限元分析方法对影响金属基复合材料的蠕变行为的因素进行了较为系统的分析。研究中主要讨论了界面特性和纤维取向角对金属基复合材料的蠕变性能的影响。研究结果发现，界面特性诸如厚度、模量和应力指数都对纤维最大轴应力和稳定蠕变率产生影响：稳态蠕变率随界面模量的增大而逐渐减小，当高于基体模量时基本保持不变；纤维轴应力的变化与蠕变率正好相反。稳态蠕变率随界面厚度、应力指数的增加而增大；而轴应力则随之减小。同时不同的纤维取向也影响金属基复合材料蠕变时的轴应力分布和稳态蠕变率。     

Calculation of Heavy Gas Spreading Over the Earth Surface by a Three-Dimensional Model

A mathematical model is constructed for motion of a heavy gas along the underlying terrain on the basis of equations of gas dynamics with allowance for the force of gravity, transfer by air masses, and turbulent diffusion. With the use of the method of coarse particles, the time dependences of the coordinates of the fore front, upper boundary, and volume of the cloud of a heavy gas in the presence and absence of wind are analyzed. It is shown that turbulent diffusion leads to a linear increase in cloud volume in time. Three-dimensional shapes of the heavy gas cloud are obtained for various ambient conditions. It is shown that, despite diffusion, the heavy gas spreads predominantly along the underlying terrain.     

一种大型结构特征值问题的并行解法

本文提出了一种求解大型结构固有频率与模态的并行解法。该方法在子空间迭代过程中,利用子结构刚度阵和质量阵并行进行凝聚,求得下一次的迭代基矢量,直到收敛。该算法在西安交通大学ELXS1-6400并行机上程序实现,计算结果表明能大幅度节省计算时间,同时也有效地节省了内存。     

A METHOD OF DETERMINING BUCKLED STATES OF THIN PLATES AT A DOUBLE EIGENVALUE

A method of determining bifurcation directions at a double eigenvalue is presented by combining the finite element method with the perturbation method. By using the present method, the buckled states of rectangular plates at a double eigenvalue are numerically analyzed. The results show that this method is effective.